A Kenmore dishwasher can be an easy way of dishwashing in the kitchen. Nevertheless, occasions may crop up when one is forced to empty the dishwasher for either cleaning or repair. It is the complete guide on how to drain a Kenmore dishwasher correctly.
Step 1: Turn off the dishwasher
Always ensure the power is turned off and all cycles are stopped before draining the dishwasher. It is to ensure that there are not any accidents, electric shock incidents, or accidents associated with electricity during this process. Switch off the dishwasher’s power button or switch.
Step 2: Access the drain pump
The drain pump is usually found at the underside of most Kenmore models. To get into it, pull out the lower rack. Remove the frame and then check if a round or square-shaped cover is on the middle or back cover.
Step 3: Prepare a container
Put a shallow bowl or towel below the drain pump zone to prevent spills when draining. It is designed to avoid a mess and ease the clean-up process. The container must, however, be big enough to carry a lot of water.
Step 4: Pull out the drain pump and clean it.
The drain pump cover is secured with screws and clips by the dishwasher model that you have. Use appropriate instruments like a screwdriver or plier to remove the lid. It is inside here that the impeller and pump for drainage are located. It is important to note also where the parts are located before they are removed.
Soft brushes or fabric are utilized to carefully clean small debris like food particles and obstacles from pumps and impellers. Ensure you pay keen attention to the impeller blades that may get blocked by food leftovers. Carefully wash the pump and impeller to make sure there is no obstruction.
Step 5: Check the drain hose
Check along the drain hose that goes into the system to see whether there are any obstructions inside it. It usually connects to the sink drain or the garbage machine in the back. If needed, straighten the hose and clear it of debris. Make sure that your drain hose is well attached. A replacement may be called for in case of severe damage or clogging of the drain hose.
Step 6: Drain the water manually
After that, you must locate the drain hole or plug at the end of your dishwasher to drain any remaining water manually. Scoop the water using a cup or a spoon into the prepared container. Avoid splashing any water into electrical parts and your kitchen floor. This procedure should be repeated until the dishwasher turns out devoid of the dishes.
Step 7: Reassemble the drain pump
Finally, reassemble the drain pump after draining and cleaning the dishwasher. Restore the clean impeller and pump in the original positions. Finally, put the drain pump cover back securely using screws and nails or clips. Ensure that it is well-sealed to avoid any leaks.
Step 8: Test the dishwasher
Ensure that the drainage system is fully operative by switching on the dishwasher inlet and running a quick rinsing cycle. Carry out a leakage test and evaluate the sounds while on the cycle. If you did not experience any problems draining the dishwasher, the drainage was successful.
Conclusion
This is a comprehensive guide on how to drain your Kenmore dishwasher, and it is easy if you follow the instructions. You can enhance dishwasher cleaning performance by regularly cleaning the drain pump and inspecting for clogs inside the drain hose. In case of persistent problems and challenges, refer to your handbook or seek advice from a licensed expert. A tidy, well-kept dishwashing machine lasts longer with shining plates every other day.
FAQ’s about ( Kenmore Dishwasher )
Q: What are some symptoms that call for draining my Kenmore dishwasher?
A: The following are some common symptoms that your Kenmore dishwasher needs to be drained.
- Dirty water that does not drain completely from the bottom of the dishwasher during a wash cycle.
- The dishwasher is not draining completely
- Unusual sounds in the dishwasher during the drain cycle.
- Water is leaking from underneath a dishwasher.
Q: When should you clean the drain pump and inspect the hose?
A: Cleaning of the drain pump and checking on the blockage in the drain hose should be done at least every six months. This way, water is trapped in the machine for a few more cycles, preventing drainage issues and prolonging the dishwasher’s lifespan.
Q: If you have a Kenmore dishwasher, what tools are required for draining the machine?
A: What you need to run and empty your Kenmore dishwasher varies depending on how your dishwasher works and the model. Nevertheless, it is necessary to have a screwdriver, pliers, a shallow container, and towels.
Q: What must I do if I cannot unscrew a drain pump, clean the impeller, and others?
A: Sometimes, you may encounter difficulties unplugging the pump and cleaning the engine. That is why it is advisable to examine the owner’s guide regarding your dishwashing machine type of operation. In addition, it is possible to call a qualified appliance repairer.
Q: What should be done if a Kenmore Dishwasher will not drain even after trying out all those steps?
A: If your Kenmore dishwasher does not drain even after applying the procedures provided in this manual, the problem with the dishwasher itself is more complicated. Therefore, consulting with a qualified domestic appliance repair specialist is advisable in such a scenario.
